From: Bobby Joe Pendleton II (bobbyjoe@chartertn.net)
Date: Sun Mar 16 2003 - 07:11:52 PST
You correct on the high reverse. You can use ATF in them IF they have been
rebuilt .My M211 uses ATF in it. It also has the Memphis Equipment manual
shift conversion in it, and it works great. I have had mine out two times
The first one I put in would not down shift to1st when you stopped. The
second one I put in had the Manual shift conversion. It is worth the trouble
to put in, just like a straight drive just no clutch pedal. and make the
truck perform better on hills and when towing.
Bobby Joe Pendleton II
MVPA #17657
----- Original Message -----
From: "william f cox" <grntrks@juno.com>
To: "Military Vehicles Mailing List" <mil-veh@mil-veh.org>
Sent: Sunday, March 16, 2003 10:00 AM
Subject: Re: [MV] xm211, cckw, help!
> Caleb,
> As I understand it, from several folks I know locally, the auto-trans in
> these trucks has a weak spot in HIGH RANGE REVERSE. But, if you always
> come to a complete stop before shifting and then always use LOW RANGE
> reverse they are more reliable. I have 2 friends who drive these and
> love the trucks.
>
> The CCKW was a WW11 GMC. The M135/M211 GMC's are " Korean War " vintage
> Hope this helps.
>
> By the way, be very careful to use the correct oil in the trans. ATF
> fluid does'nt not work in them and will fry the trans VERY quickly.
>
> Frank
>
> On Sat, 15 Mar 2003 21:07:58 -0800 "Caleb Pal, Network Operations"
> <sysop@spitfire.homelinux.com> writes:
> > Hello List,
> >
> > I was looking for a M35A2, but i found out that a local farmer has 2
> > CCKW's,
> > (I think they are 1953's), model XM211. So, I am looking for some
> > information about them. I have heard that the transmissions and or
> > transfer
> > cases are prone to failure. Is there truth to this? I am pretty sure
> > it has
> > a 302 inline 6 cylinder. One thing i was thinking about, is it
> > practical to
> > throw something like a small block chevy 305 in there? I have one
> > lying
> > around i could pop in there if it would work. I might be able to get
> > it for
> > cheep, so i guess i am also asking would it cost more in the long
> > run
> > because of transmission failure, etc. Also, i dont know what kind
> > of
> > mechanism engages the fron end. thanks a lot for any help, as usual
> > i am
> > asking tons of questions!!
> >
> > Thanks again,
> >
> > Caleb
> >
> >
> > ===Mil-Veh is a member-supported mailing list===
> > To unsubscribe, send e-mail to: <mil-veh-off@mil-veh.org>
> > To switch to the DIGEST mode, send e-mail to
> > <mil-veh-digest@mil-veh.org>
> > To reach a human, contact <ack@mil-veh.org>
> >
> >
>
>
> Frank Cox (grntrks@juno.com)
> MVPA 14530
> '45 GMC 353 DUKW
> '66 Kaiser-Jeep M35A2 w/w
> '68 M105A1 trailer
>
> ===Mil-Veh is a member-supported mailing list===
> To unsubscribe, send e-mail to: <mil-veh-off@mil-veh.org>
> To switch to the DIGEST mode, send e-mail to <mil-veh-digest@mil-veh.org>
> To reach a human, contact <ack@mil-veh.org>
This archive was generated by hypermail 2.1.4 : Wed Apr 23 2003 - 13:25:52 PDT