From: Sonny Heath (sonny@defuniak.com)
Date: Thu Nov 17 2005 - 11:31:35 PST
What would you do when you have one like the one being discussed that is
Sonny
----- Original Message -----
broken off up in the threaded hole?
From: <uniquemachine@cybcon.com>
To: "Military Vehicles Mailing List" <mil-veh@mil-veh.org>
Sent: Thursday, November 17, 2005 9:37 AM
Subject: Re: [MV] [Norton AntiSpam] Re: [MV] inverted "easy out".......
> I have had a great amount of sucess welding nuts to broken
> things and removing them, even in situations like yours. Take a
> nut that will just slip over the broken whatever and weld the inside
> of the nut to the top of the broken thing. Get good weld penetration
> to the top of the broken part first, then catch the nut. The heat also
> helps on loosening stuff up. Let everything cool and shrink back
> down and just use a wrench and unthread the broken part.
>
> Jon
> Unique Machine & Engineering
>
> On 17 Nov 2005, at 7:00, ygmir wrote:
>
>> The problem with welding onto it, is, that it's recessed an inch or
>> more inside the rim it's holding on. So, no access from the sides.
>> Only straight down. It seems one of the gadgets that are socket like
>> would be best, although, it was suggested that a piece of pipe/tube
>> just bigger than the shaft, but, smaller than the hole it's down in,
>> be placed in, then, arc welded from the inside of the tube. Sounds
>> like a good idea, too. Thanks, Henry
>>
>> ----- Original Message -----
>> From: "m35products" <m35prod@optonline.net>
>> To: "ygmir" <ygmir@onemain.com>; "Military Vehicles Mailing List"
>> <mil-veh@mil-veh.org> Sent: Thursday, November 17, 2005 5:40 AM
>> Subject: Re: [MV] inverted "easy out".......
>>
>>
>> > Sears makes a socket gadget that has teeth on the inside that
>> > supposedly will grip an irregular (for instance, rounded-off)
>> > fastener. Bob Vila says that it works, and who are we to doubt Ol'
>> > Bob?
>> >
>> > How about welding something to it, and getting some more material on
>> > the shaft?
>> >
>> > apb
>> >
>> > ----- Original Message -----
>> > From: "ygmir" <ygmir@onemain.com>
>> > To: "Military Vehicles Mailing List" <mil-veh@mil-veh.org>
>> > Sent: Thursday, November 17, 2005 1:29 AM
>> > Subject: [MV] inverted "easy out".......
>> >
>> >
>> >> Hi all,
>> >> Ok,
>> >> It's a strange question:
>> >> Is there an "inverted" easy out type tool?
>> >> Like, a socket with splines on a left hand twist, or, something
>> >> like that? I have a broken, threaded shaft, recessed in a hole. If
>> >> I could beat a socket type arrangement on it, and, turn left, I
>> >> could get it out. It's to deep to cut any type of shape into, like
>> >> a slot and, there isn't enough
>> > room
>> >> to grind a flat spot or more on the outer edge of said shaft.
>> >> But, a socket type arrangement if it could be pounded on and had
>> >> the left threaded splines, maybe tapered, that would allow for
>> >> counterclockwise turning....... Any help, ideas are appreciated.
>> >> Thanks, Henry
>> >>
>> >>
>> >>
>> >> ===Mil-Veh is a member-supported mailing list===
>> >> To unsubscribe, send e-mail to <mil-veh-off@mil-veh.org>
>> >> To reach a human, contact <ackyle@gmail.com>
>> >> Visit the searchable archives at http://www.mil-veh.org/archives/
>> >
>> >
>>
>>
>>
>> ===Mil-Veh is a member-supported mailing list===
>> To unsubscribe, send e-mail to <mil-veh-off@mil-veh.org>
>> To reach a human, contact <ackyle@gmail.com>
>> Visit the searchable archives at http://www.mil-veh.org/archives/
>>
>>
>
>
>
>
> ===Mil-Veh is a member-supported mailing list===
> To unsubscribe, send e-mail to <mil-veh-off@mil-veh.org>
> To reach a human, contact <ackyle@gmail.com>
> Visit the searchable archives at http://www.mil-veh.org/archives/
>
>
> --
> Internal Virus Database is out-of-date.
> Checked by AVG Free Edition.
> Version: 7.1.361 / Virus Database: 267.12.5/147 - Release Date: 10/24/2005
>
This archive was generated by hypermail 2.1.4 : Tue Jul 18 2006 - 21:32:02 PDT