>Hello,
>
>I am inquiring on cost for some parts that I am looking for. I own a 68
>kaiser 2 1/2 ton cargo truck. The designation is M35A2 (no winch).
>I believe the engine was overhauled by T.E.A.D in 1990. Here is
>a list of parts that I would like to know about... price, shiping, and
>availability.
>
>(note: I would like quality parts, I will be showing this vehicle and need
>parts that need light restoring or are already like new.)
>
>
>1) Canvas complete cab w/bows and hardware.
>
>2) Complete weatherstrip kit for cab
>
>3) 24v Heather motor (motor only please)
>
>4) Hard Top cab for 2 1/2 ton & Hardware
>
>5) Steering wheel and complete horn button assy.
>
>6) Canvas tarplan for rear bed (I have troop seats.... so, I guess
> I'm pricing bows, 3 pieces of canvas, and lashing ropes.
>
>7) Pioneer tool set (ax, pick, shovel)
>
>8) 2 canvas lashing that hold the pick/shovel/ax in place.
>
>9) Spare tire wrenches & Jack
>
>10) 4 marker light bulbs (24v) the little ones.
>
>11) The part that attaches to the spare tire cable.... I have the
> winching assy that brings the tire up... I have the cable on the
> spindal... but the cable is just hanging there without an end on it.
> I need the piece that fits through the rim with the 2 stud nuts and
> holds the tire to the cable. (I also need the studs & Nuts)
>
>12) The air hose assy. (supposed to be in tool box) comes with
> a gauge on the line and connects at different places around
> the truck to inflate it's own tires.
>
>13) Glove box ruber gasket seal
>
>14) Directly under the driver is some clutch linkage that has come
> apart.... there is a pin and some sort of retainer clip that holds
>the
> clutch linkage together. (all of this under the drivers feet area)
> I have the pin that holds them together... but its wraped with wire
> to hold the pin in position... I need the retainer pin that snaps
(I
> guess) around the beveled pin and holds the linkage tight.
> (this part is very important to me and I hope you can pull one
> from another truck) thank you.
>
> 15) Oil filters for servicing
>
> 16 Air cleaner for servicing
>
> 17) Fuel Filters for servicing
>
> 18) Metal replacment fuel injector lines with fittings. For entire fuel
> system under the hood.
>
> 19) Manifold Heater assy. I only need the part that screws into the
> manifold that has 2 fuel lines running to it. Mine drips fuel
> directly onto my trubo while operating. Please pick me one
> that doesn't need to be repaired.
>
> 20) 3 pairs of single sized Ice breaker or normal tire chains.
>
> 21) A servicing manual would be helpful. I have a general maunal but
> doesn't have much to say about what and where things are.
>
>22) On the dash, the heater switch is supposed to have its own added
> drop plate for the switch to be located in. (correct)? somone has
> just drilled a hole in the dash and installed it... its unlabeled
> aswell. I would like everything (including on/off switch) to make
> the heather switch correct inside the cab.
>
>23) I need the front wood for the cargo bed.... The troop seats line
> the sides with wood slats.... but I need the wood for behind the
> cab. I have the metal hardware that fits into the cargo bed for the
> front... I just need the oak rails and the 2 oak uprights that fit
> inside the 2 front metal supports.
>
>24) Dash Rifle Mount kits for 2 Rifles.
>
>25) High/Low Beam indicater bulb for the dash.. The one on the
> turnsignals went out so I swapped that bulb with the hi/low's for
> a bit.... (are those the same bulb as the side marker ones?
> if so.. send me about 10 of them.)
>
> 26) Fording snorkle? anything you have for fording equipment would
> of assistance for me.
>
> 27) I need a different air breather for the intake... Its a round
> muishroomed shaped thing that fits through the side of the
> hood and sits above the LF fender. It attaches to the Air
> Cleaner TUB and I don't need the clamp. Just the mushroom.
> (no dents please.. mine has them already)
>
> 28) (bridge marker tags for the grille) .... I have a round shaped
> plate in my grille that is supposed to contain 2 numbers for
> bridge weight identification... if you have any for a 2 1/2 ton
> please ad to my itemized quote. thank you.
>
>
> OK.. I don't know if I can afford all of this stuff or not... so
please
> quote me ammounts in a list form like I did... if possible.
>
> Shipping needs to be there for me to see too OK?
>
> Damon Lehr
> 1424 NE 195th
> Portland, Or
> 97230
>
> Thank you for your time...
> If your prices are low enough for me
> and you have a good selection of parts
> that I need.. I will be purchasing from you.
>
>
>
===
To unsubscribe from the mil-veh mailing list, send the single word
UNSUBSCRIBE in the body of a message to <mil-veh-request@skylee.com>.