HAMMER: Originally employed as a weapon of war, the hammer nowadays
is used
as a kind of divining rod to locate expensive or rare parts not far
from the object
we are trying to hit. Cost of hammer has no bearing on functionality
, however true
US Govt. surplus Hammer, Sledge ,2.5 pound , Short handle, non
sparking, does add
a little savage, twisted panache to the repair process.
MECHANIC'S KNIFE: Used to open and slice through the contents of
cardboard
cartons delivered to your front door; works particularly well on
boxes
containing seats and replacement NOS canvases.
ELECTRIC HAND DRILL: Normally used for spinning steel Pop rivets in
their
holes until you die of old age, but it also works great for drilling
mounting holes in fenders through the brake line that goes to the
rear
wheel.
PLIERS: Used to round off bolt heads.
HACKSAW: One of a family of cutting tools built on the Ouija board
principle. It transforms human energy into a crooked, unpredictable
motion,
and the more you attempt to influence its course, the more dismal
your
future becomes.
VISE GRIPS: Used to round off bolt heads. If nothing else is
available,
they can also be used to transfer intense welding heat to the palm of
your
hand.
OXYACETYLENE TORCH: Used almost entirely for lighting various
flammable
objects in your garage or on your MV on fire. Also handy for
igniting the grease inside
a brake drum you're trying to get the bearing race out of.
WHIT WORTH SOCKETS: Once used for working on older British and
Commonwealth MV's and
motorcycles, they are now used mainly for impersonating that 9/16 or
1/2 inch socket
you've been searching for the last 15 minutes.
DRILL PRESS: A tall upright machine useful for suddenly snatching
flat
metal bar stock out of your hands so that it smacks you in the chest
and
flings your beer across the room, splattering it against that freshly
painted part you were drying.
WIRE WHEEL: Cleans rust off old bolts and then throws them somewhere
under
the workbench with the speed of light. Also removes fingerprint
whorls and
hard-earned guitar calluses in about the time it takes you to say,
"Ouc...."
HYDRAULIC FLOOR JACK: Used for lowering an MV to the ground after
you have installed your new front brake setup, trapping the jack
handle
firmly under the front fender.
EIGHT FOOT LONG DOUGLAS FIR 2X4: Used for levering an MV upward off
a hydraulic jack.
TWEEZERS: A tool for removing wood splinters.
PHONE: Tool for calling your neighbor to see if he has another
hydraulic
floor jack.
Snap-On GASKET SCRAPER: Theoretically useful as a sandwich tool for
spreading mayonnaise; used mainly for getting dog-doo off your boot.
E-Z OUT BOLT AND STUD EXTRACTOR: A tool that snaps off in bolt holes
and
is ten times harder than any known drill bit.
TIMING LIGHT: A stroboscopic instrument for illuminating grease
buildup.
TWO TON HYDRAULIC ENGINE HOIST: A handy tool for testing the tensile
strength of ground straps and brake lines you may have forgotten to
disconnect.
CRAFTSMAN 1/2 x 16 INCH SCREWDRIVER: A large motor mount prying tool
that
inexplicably has an accurately machined screwdriver tip on the end
without
the handle.
BATTERY ELECTROLYTE TESTER: A handy tool for transferring sulfuric
acid
from a car battery to the inside of your toolbox after determining
that your
battery is dead as a doornail, just as you thought.
AVIATION METAL SNIPS: See hacksaw.
TROUBLE LIGHT: The mechanic's own tanning booth. Sometimes called a
drop
light, it is a good source of vitamin D, "the sunshine vitamin,"
which is
not otherwise found under MV's at night. Health benefits aside, it's
main purpose is to consume 40 watt light bulbs at about the same rate
that
105 mm howitzer shells might be used during, say, the first few hours
of
the Battle of the Bulge. More often dark than light, its name is
somewhat
misleading.
PHILLIPS SCREWDRIVER: Normally used to stab the lids of old style
paper-and-tin oil cans and splash oil on your shirt; can also be
used, as
the name implies, to round off Phillips screw heads.
AIR COMPRESSOR: A machine that takes energy produced in a coal
burning
power plant 200 miles away and transforms it into compressed air that
travels by hose to a Chicago Pneumatic impact wrench that grips rusty
bolts
last tightened 40 years ago by someone in Sindelfingen, and rounds
them off.
PRY BAR: A tool used to crumple the metal surrounding that clip or
bracket
you needed to remove in order to replace a 50 cent part.
HOSE CUTTER: A tool used to cut hoses 1/2 inch too short.
Now that you have been properly informed , go forth and leave no
thread unstripped.
Ron
===
To unsubscribe from the mil-veh mailing list, send the single word
UNSUBSCRIBE in the body of a message to <mil-veh-request@skylee.com>.