From: Horrocks, Aaron (ACHb@pge.com)
Date: Tue Aug 05 2003 - 13:08:11 PDT
If you're going to use the bounce method, please set up at least one video camera to film this little operation, so it can be a future "Stupid MV Trick"
Isn't there some sort of portable ramp that the military uses for such operations???
Aaron Horrocks
-----Original Message-----
From: Glen Bedel [mailto:GBedel@designforum.com]
Sent: Tuesday, August 05, 2003 12:46 PM
To: Military Vehicles Mailing List
Subject: Re: [MV] Stupid question # ......
I figure after the 5 ton stops bouncing and pile driving my neighbors
mailbox it would still move.
-----Original Message-----
From: Mugno, Anthony [mailto:AMugno@SITAAPS.org]
Sent: Tuesday, August 05, 2003 3:38 PM
To: 'Glen Bedel'; Military Vehicles Mailing List
Subject: RE: [MV] Stupid question # ......
Dunno Never tried it with one of these.
Actually your problem reminded me of when I had a similar situation in my
younger days. I solved it using the method I described below. It wasn't
pretty.............
-----Original Message-----
From: Glen Bedel [mailto:GBedel@designforum.com]
Sent: Tuesday, August 05, 2003 3:20 PM
To: Military Vehicles Mailing List
Subject: Re: [MV] Stupid question # ......
Ok how high will the m818 bounce after this is done?
-----Original Message-----
From: Mugno, Anthony [mailto:AMugno@SITAAPS.org]
Sent: Tuesday, August 05, 2003 3:09 PM
To: Military Vehicles Mailing List
Subject: Re: [MV] Stupid question # ......
Attach a stout chain to the chassis of the unit on the hauler. Take the
other end of the chain and attach it to something really immobile. Get in
the hauler and put in low gear then stomp on the gas pedal.
It works every time!! (well almost anyhow)
-----Original Message-----
From: Mark J. Blair [mailto:ke6myk_mvlist@sbcglobal.net]
Sent: Tuesday, August 05, 2003 3:00 PM
To: Military Vehicles Mailing List
Subject: Re: [MV] Stupid question # ......
Glen Bedel wrote:
> Ok how to get 2 M818s off a 48'flatbed trailer. Possible deck ht. at
> 54"
I don't think it's a stupid question. Other suggestions already posted are
good. There's another option, too: Lift them off, one end at a time, with a
commercial wrecker. That's how we unloaded my M543A2 5-ton wrecker when no
loading ramps were available.
1) The commercial wrecker picked up the back end of my truck with it's axle
lift.
2) The truck driver pulled hte tractor/trailer forward until the front
wheels
of my truck were at the back edge of the trailer.
3) The wrecker lowered my truck to the ground, so the rear wheels were on
the
ground and the fronts were on the trailer.
4) The wrecker pulled around and lifted up the front end of my truck with
its
crane.
5) The truck driver pulled the trailer out the rest of the way.
6) The wrecker lowered my truck to the ground.
When my Gama Goat arrived, I did the same thing, using my own wrecker. The
lockout truss was installed on the goat so it wouldn't bend in the middle.
Here are pictures for inspiration:
http://www.qsl.net/ke6myk/greentruck/truck3/pics.html
-- Mark J. Blair, NF6X <ke6myk@sbcglobal.net> PGP 2.6.2 public key available from http://www.keyserver.net/ Web page: http://www.qsl.net/ke6myk/===Mil-Veh is a member-supported mailing list=== To unsubscribe, send e-mail to: <mil-veh-off@mil-veh.org> To switch to the DIGEST mode, send e-mail to <mil-veh-digest@mil-veh.org> To reach a human, contact <ack@mil-veh.org>
===Mil-Veh is a member-supported mailing list=== To unsubscribe, send e-mail to: <mil-veh-off@mil-veh.org> To switch to the DIGEST mode, send e-mail to <mil-veh-digest@mil-veh.org> To reach a human, contact <ack@mil-veh.org>
===Mil-Veh is a member-supported mailing list=== To unsubscribe, send e-mail to: <mil-veh-off@mil-veh.org> To switch to the DIGEST mode, send e-mail to <mil-veh-digest@mil-veh.org> To reach a human, contact <ack@mil-veh.org>
===Mil-Veh is a member-supported mailing list=== To unsubscribe, send e-mail to: <mil-veh-off@mil-veh.org> To switch to the DIGEST mode, send e-mail to <mil-veh-digest@mil-veh.org> To reach a human, contact <ack@mil-veh.org>
This archive was generated by hypermail 2.1.4 : Sat May 07 2005 - 20:23:34 PDT