From: Rikk Rogers (Rkltd@swbell.net)
Date: Thu Nov 17 2005 - 07:21:31 PST
Carbide center punch, drill center of said stud (as deep as can, use lots of
oil in process) EZout to fit.
Careful to be in center and not cut the threads in hole.
If its not hard-tight a small EZout will work.
Rikk Rogers
RK Lion Ltd.
R3 Box 423 B
Wellston OK 74881
MVPA 22345
Hard Wire 405.258.6767
Cell 405.664.1400
-----Original Message-----
The problem with welding onto it, is, that it's recessed an inch or more
From: Military Vehicles Mailing List [mailto:mil-veh@mil-veh.org]On
Behalf Of ygmir
Sent: Thursday, November 17, 2005 9:00 AM
To: Military Vehicles Mailing List
Subject: Re: [MV] inverted "easy out".......
inside the rim it's holding on. So, no access from the sides. Only straight
down.
It seems one of the gadgets that are socket like would be best, although, it
was suggested that a piece of pipe/tube just bigger than the shaft, but,
smaller than the hole it's down in, be placed in, then, arc welded from the
inside of the tube. Sounds like a good idea, too.
Thanks,
Henry
----- Original Message -----
From: "m35products" <m35prod@optonline.net>
To: "ygmir" <ygmir@onemain.com>; "Military Vehicles Mailing List"
<mil-veh@mil-veh.org>
Sent: Thursday, November 17, 2005 5:40 AM
Subject: Re: [MV] inverted "easy out".......
> Sears makes a socket gadget that has teeth on the inside that supposedly
> will grip an irregular (for instance, rounded-off) fastener. Bob Vila
> says
> that it works, and who are we to doubt Ol' Bob?
>
> How about welding something to it, and getting some more material on the
> shaft?
>
> apb
>
> ----- Original Message -----
> From: "ygmir" <ygmir@onemain.com>
> To: "Military Vehicles Mailing List" <mil-veh@mil-veh.org>
> Sent: Thursday, November 17, 2005 1:29 AM
> Subject: [MV] inverted "easy out".......
>
>
>> Hi all,
>> Ok,
>> It's a strange question:
>> Is there an "inverted" easy out type tool?
>> Like, a socket with splines on a left hand twist, or, something like
>> that?
>> I have a broken, threaded shaft, recessed in a hole. If I could beat a
>> socket type arrangement on it, and, turn left, I could get it out. It's
>> to
>> deep to cut any type of shape into, like a slot and, there isn't enough
> room
>> to grind a flat spot or more on the outer edge of said shaft.
>> But, a socket type arrangement if it could be pounded on and had the left
>> threaded splines, maybe tapered, that would allow for counterclockwise
>> turning.......
>> Any help, ideas are appreciated.
>> Thanks,
>> Henry
>>
>>
>>
>> ===Mil-Veh is a member-supported mailing list===
>> To unsubscribe, send e-mail to <mil-veh-off@mil-veh.org>
>> To reach a human, contact <ackyle@gmail.com>
>> Visit the searchable archives at http://www.mil-veh.org/archives/
>
>
===Mil-Veh is a member-supported mailing list===
To unsubscribe, send e-mail to <mil-veh-off@mil-veh.org>
To reach a human, contact <ackyle@gmail.com>
Visit the searchable archives at http://www.mil-veh.org/archives/
This archive was generated by hypermail 2.1.4 : Tue Jul 18 2006 - 21:32:01 PDT